A.1 Fixed Reference Channels for receiver sensitivity and in-channel ... Base Station RF Bandwidth edge: frequency of one of the edges of the Base Station ...
#32.
GPS sensitivity questions and its HW RF consideration
同等的機構條例或合約條款中所定義的「限制的電腦軟體」來交付和授權。 ... 時，低於-100 dBm 之產生器和接收機功能的效能會降低。 ... FM 輸入電平靈敏度：.
#57.
The Effects of Adjacent Channel Rejection ... - Texas Instruments
This allows input signals up to +4 dBm, but the tradeoff is lower receiver sensitivity. At the other end of the RF processing chain from the LNA is the input to ...
analog and RF circuit design, Christian C. Enz further divided ... substantially reduced the requirements on the sensitivity of receiver front-end. All.
#61.
LTE筆記: RSRP, RSSI and RSRQ - Castle on a Cloud
#65.
Inrush Current Analysis - USB-IF Compliance Updates
134, January, 2020, Receiver Sensitivity (EL_17) and Squelch (EL_16) Histogram measurement areas defined, Undefined measurement window for the histogram ...
#90.
A7105 Preliminary 2.4GHz Transceiver - All Products
dBm. Receiver sensitivity. @ BER = 0.1%. Data rate 500K. -96. dBm ... FIFO 操作模式下，RF chip 會依使用者定義的封包格式，將.
#91.
勁達Nordic nRF52833藍牙外接天線模組BT5.2模塊 ... - 露天拍賣
‧-95dBm sensitivity in 1Mbps Bluetooth low energy (BLE) mode ‧-103dBm sensitivity in 125Kbps BLE mode (long range) ‧+8 dBm TX power (down to ...
#92.
3GPP TS 36.104 V12.10.0 (2016-01)
A.1 Fixed Reference Channels for reference sensitivity and in-channel ... Base Station RF Bandwidth edge: frequency of one of the edges of the Base Station ...
#93.
Receiver Blocking Analysis Application Note
in sensitivity. In general, receiver blocking occurs in one of three ways: • Preamplifier overload – caused by strong RF signals which.
#94.
DVS 系列工業級非網管型乙太網路交換器使用手冊
與MDI-X(HUB/Switch-type)自動跳線偵測模式，腳位定義如下：. 10/1000Base-T(X) ... budget of 16dBm to a value below the Rx sensitivity.
rx sensitivity定義 在 Re: [問題] Link budget 怎麼算起來都是0... - 看板comm_and_RF 的推薦與評價
※ 引述《xm3vul3h06 (Silkworm)》之銘言：
: 各位高手好，小弟最近在計算Link budget
: 因為是第一次接觸所以翻了一些paper
: 得到以下幾條定義式
: Noise floor=-174+noise figure+10log(BW)
: SNR=Rx Power(dBm)-Noise floor
: Sensitivity=noise floor+SNR
: Link budget=Rx Power-Sensitivity
: 可是在第3式就把sensitivity定義成Rx Power了
: 那第4式怎麼減都只會等於0啊
: 其中肯定有什麼誤會
: 請各位高手救命啊Orz
第三式的SNR 指的是SNR_min
也就是接收機的解調門檻
第二式的SNR 指的是SNR_signal
也就是你RX訊號的SNR
這兩者是不同的
所以很多人常搞混一點 人家都說SNR越大越好
但是SNR越大 帶入第三式 Sensitivity越爛啊?
問題就出在把SNR_signal跟SNR_min搞混
SNR_min是越小越好 表示你接收機解調門檻越低 越容易解調
亦即在可解調的前提下 可以接收到越微弱的訊號
而越大越好 指的是SNR_signal
舉個例 假設接收機SNR_min = 4dB
而你打一個-100 dBm的訊號 其SNR_signal為10 dB
表示啥? 表示你靈敏度可以到達-106 dBm 推導如下 :
-100 dBm SNR_signal = 10dB
-101 dBm SNR_signal = 9dB
-102 dBm SNR_signal = 8dB
-103 dBm SNR_signal = 7dB
-104 dBm SNR_signal = 6dB
-105 dBm SNR_signal = 5dB
-106 dBm SNR_signal = 4dB = SNR_min
那如果同樣-100 dBm的訊號 其SNR_signal為20 dB
則靈敏度可以壓到-116 dBm 故SNR_signal越大越好
不過在計算Link Budget時
真正關鍵是Noise Figure
因為靈敏度公式中
Thermal Noise你改變不了 (除非你在低溫下測試)
頻寬跟SNR_min 你也改變不了
你唯一能改變的 就只有Noise Figure
Link Budget是計算說 我這樣的RX Path設計
能否達到靈敏度要求?
可以 => 啊是好多少?
不行 => 要怎樣改善?
改善之道 通常也只能透過RX Path整體Noise Figure的壓低
看是要額外再掛LNA還怎樣
--
推 obov: 有人賣腦 有人賣肝 有人天天給人家幹
--
※ 發信站: 批踢踢實業坊(ptt.cc), 來自: 220.132.62.158
※ 文章網址: https://www.ptt.cc/bbs/comm_and_RF/M.1471957817.A.395.html
... <看更多>